2SD Datasheet, Equivalent, Cross Reference Search. Type Designator: 2SD Material of Transistor: Si. Polarity: NPN. Maximum Collector Power. D Datasheet PDF Download – 2SD, D data sheet. D(TRANSISTOR) NTE Equvilent NTE TRANSISTOR NPN SILICON 60V IC=1A GIANT TO CASE AUDIO AMP & DRIVER COMP’L NTE Data Sheet.
|Published (Last):||2 July 2014|
|PDF File Size:||8.92 Mb|
|ePub File Size:||20.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
Where, the value of VBE will be 5v for this transistor. This data sheet contains data from the product. How to use 2N Submitted by webmaster on 12 December Added trsnsistor modified specifications as data sheet was updated.
Supplementary data will be. This data sheet contains preliminary data ; supplementary data may be published later. Used in inverter and converter circuits Used for making siren or dual Led or Lamp flasher. This data sheet contains data from the product specification. Also note that the load current should be less than mA here ma.
The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.
The 2N is a commonly used PNP transistor. If made high 5V the motor will stop rotation. This transistor has only a gain value ofhence not suitable for amplifier circuits. SHARP reserves the right to make changes in the specifications, characteristics, datamaterials.
Complete Technical Details can be found at the 2N datasheet given at the end of this page. When used as a switch, it can be operated in saturation region and cut-off region.
So if you looking for a PNP transistor that could switch high voltage loads within 0. Where to use 2N Changefrom the voltage levels specified in the DSP56L Technical Data sheetbut does not affect theset to 0.
This data sheet contains data from the preliminary. This data sheetthe design and supply the best possible product. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around 5V.
2SD Datasheet, Equivalent, Cross Reference Search. Transistor Catalog
This data sheet contains data from the preliminary specificationsheet contains data from the product specification. Previous 1 2 Philips Semiconductors reserves the right to make. If supply is provided to the base pin it stops conducting current between emitter and collector and said to be in OFF state.
Run key Sets the parameter number or changes the numerical data such, etc. Product data ; ECNdata 2-bit bi-directional low voltage translator GTL Data sheet status Level I Data sheet status Objective data Product status  Development Definitions This transisror sheetright to change the specification in any manner without notice.
For the protection of transistor a resistance added in series with it.
2SD400 Datasheet, Equivalent, Cross Reference Search
The die was not changed. This data sheet contains data. This data sheet contains. Note that for PNP transistors the loads should be connected in the collector side as shown below.
Can be used in Darlington Pair.
D400 Low-Frequency Power NPN Transistor
When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. TL — Programmable Reference Voltage. Philips Semiconductors reserves the right to change the specification in any manner without notice. D transistor data Abstract: For finding the value of that resistor you can use the formula:.
D(TRANSISTOR) NTE Equivalent NTE TRANSISTOR NPN SILICO – Wholesale Electronics
This data sheet contains data from the preliminary specification. M3D PBSSZ May pb free transistor and ic equivalent data smd transistors code free transistor free download transistor and ic equivalent data. This data sheet contains final product specifications. If we provide ground to the base pin then the transistor will be in reverse biased and said to be turn ON.
Trnasistor 2N transistor is commonly used as a switching device.
Supplementary data willwithout notice, in order to improve the design and supply the best possible product. For finding the value of that resistor you can use the formula: It very much similar to the bc transistor except for that it has high collector to emitter voltage and hence high voltage loads can be toggled.
No abstract text available Text: So, from that you can find the value of resistance to be added in series with it. This data sheet contains data from thethe best possible product.